Top 10 typical forklift mishaps ， forklift procedure must focus on these issues ！.

Do not undervalue the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Case 3: The width of the forklift cargo goes beyond the allowed size of the path and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be risk-free prior to starting.
3. When the forklift begins with a load, the vehicle driver ought to initially confirm that the load is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole needs to be tilted in reverse. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the stability of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal needs to be issued initially. High-speed sharp turns are restricted. High-speed sharp turns will create the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with tons unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and should keep a certain security distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest setting that does not impede the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks must be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In unique scenarios, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping things, the forklift must be stopped with the brake. .
4. The speed of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork idea need to not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to raise personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the Stand-on Electric Pallet Stacker goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be checked, and fuel, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you experience someone before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning ought to not be as well sharp to stop the Stand-on Electric Pallet Stacker tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll things.
7. It is not enabled to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844